Replace – Install new Flash card in Cisco router

Today I replaced Cisco 64MB Flash card with 512MB LEXAR

The whole procedure is pretty simple just make a copy of your current IOS, just insert your current Flash card it to the computer with TFTP server installed and copy .bin file to the TFTP folder.
Insert new flash card to the router and power it on.
You will start in ROMMON state, than follow those steps:

Upgrade ROMMON initialized
rommon 1 > IP_ADDRESS=192.168.1.167
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=192.168.1.1
rommon 4 > TFTP_SERVER=192.168.1.20
rommon 5 > TFTP_FILE=c2801-adventerprisek9-mz.124-24.T7.bin
rommon 6 > tftpdnld

          IP_ADDRESS: 192.168.1.167
      IP_SUBNET_MASK: 255.255.255.0
     DEFAULT_GATEWAY: 192.168.1.1
         TFTP_SERVER: 192.168.1.20
           TFTP_FILE: c2801-adventerprisek9-mz.124-24.T7.bin
        TFTP_MACADDR: 00:17:f3:ff:a2:a5
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: Yes
             FE_PORT: 0 
       FE_SPEED_MODE: Auto Detect

Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n:  [n]:  y

Receiving c2801-adventerprisek9-mz.124-24.T7.bin from 192.168.1.20 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!...
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Validating checksum.
Copying file c2801-adventerprisek9-mz.124-24.T7.bin to flash:.
program load complete, entry point: 0x8000f000, size: 0xcb80

Format: Drive communication & 1st Sector Write OK...
Writing Monlib sectors.
.......................................................................................................
Monlib write complete 

Format: All system sectors written. OK...
Format: Operation completed successfully.

Format of flash: complete
program load complete, entry point: 0x8000f000, size: 0xcb80

rommon 7 >boot

Wait until new flash will be extracted…

R1#sh flash all
-#- --length-- -----date/time------ path
1     50803300 Feb 22 1907 17:31:44 c2801-adventerprisek9-mz.124-24.T7.bin

461774848 bytes available (50806784 bytes used)

******** ATA Flash Card Geometry/Format Info ********

ATA CARD GEOMETRY
   Manufacturer Name      
   Model Number           LEXAR ATA FLASH     
   Serial Number          11154241339199092021
   Firmware Revision      V1.00   
   Number of Heads        16    
   Number of Cylinders    994   
   Sectors per Cylinder   63    
   Sector Size            512   
   Total Sectors          1001952

ATA PARTITION 1 INFO
   Start Sector           63    
   Number of Sectors      1001889
   Size in Bytes          512967168
   File System Type       FAT16
   Number of FAT Sectors  245   
   Sectors Per Cluster    16    
   Number of Clusters     62571 
   Number of Data Sectors 1001136
   Base FAT Sector        111   
   Base Root Sector       601   
   Base Data Sector       633   

ATA MONLIB INFO
   Image Monlib size      117868
   Disk Monlib Size       52664 
   Disk Space Available   56320 
   Name                   piptom-atafslib-m
   Start sector           2     
   End sector             104   
   Updated By             
   Version                1